WHY IS THE ADDRESS WHICH WE ARE WRITING ABOUT ( A DEFAULT INTERNET PROTOCOL ADDRESS?, the default Internet Protocol address, is employed on private networks by means of a Linksys router. Also, it can be employed by other devices which are connected to private networks (meaning that they are restricted to the Linksys system). There are some other default addresses which are frequently used, some of them being as well as, but they are reserved for private use by the Internet Assigned Numbers Authority. Thus, the primary aim of this default address for Linksys is providing an address for network administrator or the end-user so as to be linked to the router of the network and to carry out a configuration or some administration functions for the said network.

Recommended Reading :   

How To Setup a Linksys Wireless Router

How To Setup Your Netgear Wireless Router


The address is usually employed for accessing the webpage of the Linksys router setup. Thus, the end-users usually log onto this page so as to change or set up the wireless safety mode, or to change and set up the network name (or SSID), as well as to change or set up the key for the network security.


These are the steps we are to undertake to access the said setup:

  1. It is necessary to switch on the LinkSys router. After that, you should link the PC with the router by way of an Ethernetcable (this should be done in one of the total of 4 Ethernet ports which can be found in the back or the rear of the piece of equipment). It is relevant to take be aware that a Linksys router call for connecting to the router by employing the Ethernet technique– in other words, take care not to support the link by way of broadband or
  2. Start the web browser of the computer. After that, type in into the address bar of the browser and push the Return or the Enter key. Many users type 192.168.l.1 or 192.168.l.0 and this doesn’t launch the admin web page, so be careful.
  3. Type in the username and the password which you had set already for use on the router. In the case that you are employing a brand new router or failed to alter the factory default settings, then the default username for a recent Linksys router is the following: blank or no entry for the username and, the password being admin.
  4. The menu option Wireless should now be clicked. After that, the “Configuration View” should be set to “Manual” with the purpose of seeing the network name (or the SSID) used by the broadband network which you are using.
  5. Pick the menu option “Wireless Security.” Take note of the “Security Mode” as well as the “Passphrase” being used on the network. In the case that they are not set, they can be entered at that moment. In fact, newer models of Linksys routers will ask you to enter 4 passphrases for the network. The, the “TX Key” entry is bound to correspond with the passphrase which is active on the network. Note that the passphrases are case sensitive for Linksys wireless networks are case sensitive, as opposed to pure Windows apps.
  6. The last step is logging out of the router menu for setting up and then disconnect the computer from your router.

The default address which is our topic – – also has another purpose, that being the resetting of the Linksys router to its factory defaults. Why does this need arise? Usually when it happens that a specific end-user has forgotten his or her network passphrase or the router passphrase or login. Also it can be the case that there are constant router issues which need to be resolved. So how is this done? These are the steps.

  1. You need to locate the button for a reset which can be found on the router back or rear. When you find the button, press it for ten seconds (this is valid for an 802.11N supported Linksys device) or thirty seconds for router which are of an older date – and the device needs to be switched on. When the router indication lights are turned back on (the lights for the Internet, the Power light and the WLAN light), then you can let go of the button.
  2. Use an Ethernet cable in order to establish a link between the router and the computer. The majority of Linksys routers have as many as 4 Ethernet ports which can be found on the back of the said device located, and next to the button for reset. In fact, the Ethernet cable is inserted into any port.
  3. Then start the web browser of the computer you are using. In case you are working on a Mac, there have been issues with the browser called Opera and its linking to a Linksys router. If this happen, just switch to Mozilla Firefox in order to set upa good connection with the router.
  4. After the third step, you need to enter (not 192.168.l.1 or 192.168.l.0) into the address bar of the web browser, and after that, select the “enter” or the “return” key. The result is that the page for the Linksys router setup will be displayed. To end this step, type in “admin” for the login name (or no name, depending on the router’s age) while the passphrase is “admin.”
  5. The last step is as follows: you need to continue with the setup to the Linksys router I order to establish a network name (or SSID), an encryption type, as well as passwords for the network.

The mentioned default IP address has another purpose, expect as quoted above. It is also used for taking careful measured for home network safety. In point of fact, while hurrying to obtain a home wireless network, a number of users skip the necessary steps which need to be carried out in the purpose of establishing basic wireless network safety. There are some newer models of routers which more or less compelend-users to carry out a procedure of setting up network safety, but many do not have this safety measure installed. What you need to do to set up a wireless home safety is the following:

  • You first need to alter the router’s default username as well as password. A great number of users of PCs presume that the routers they are using at home are secure and that no one can access them without the proper network password. However, it is a fact that there is considerable vulnerability in use and if router logins and passwords are set to default settings, then the setup configuration menu can make use of the address IP and even change the settings. Therefore it is recommended to change the default IP into another one from the same IP range. Just make sure not to enter 192.168.l.1 or 192.168.l.0. It is the most common mistake you can do and which can cause you troubles and waste your time.
  • You need to set up a unique SSID or network name. Routers like Linksys as well as some other ones will have a default SSID which is shown to the users located within the device’s range and which is usually “linksys.” To know the SSID of a network is sure to be a great deal of help to all those who wish to force an entry into our network. However, it is possible to alter the SSID by way of the router setup page which must not include the the default corporate name.
  • Now switch on the wireless network safety. It is important to pick the most powerful encryption form which has the support of all the wireless devices located in our homes. In fact, the safety type is chosen in the menu of the wireless router configuration. In the case that you have selected the WEP standard, make sure that you have established a routine for changing the password (usually a monthly routine is the best for most people) if it should happen that your password was cracked.
  • Think about facilitating MAC address filtering, as every device which can be connected to a network has a physical or MAC address. In fact, wireless routers have the ability to track and employ a MAC address for the purpose of filtering network access. This can help to add an additional layer of safety, although it must not be the single means of network safety which is being used. MAC filtering can be more effective if it is combined with wireless encryption.
  • The next step is turning off the SSID Broadcast. A number of wireless routers give the option of automatically broadcasting the SSID at regular intervals. However, this may boost the chance that someone undesirable can try to get access. We know those people as well as devices which will be linking to our home network so the network name can be provided for users for configuration of the device. Also, they ought to be disabled on the setup page of the Linksys router.
  • It is best to steer clear of auto-linking in order to unlock wireless networks. In fact, this step has nothing to do with the use of for the configuring of the wireless router, although hit can be important. As a matter of fact, if there is a network which is open and you link to that instead of the network you usually use, the result can be an exposing of the home network as well as the wireless device to an additional safety risk. It is best to disconnect manually after accepting a link to an open network, as this will help put off future links.
  • Switch on the router’s firewall as well as all the computers on the network. You can configure the firewall on a Linksys router by way of the configuration panel. By switching this firewall as well as all the firewalls of the clients which are using the computers which have access to the network are sure to guarantee that the network as well as the individual PCs have protection against network intruders.

Now when you have read about some specific networking tasks, the use of, and why you should take care not to type 192.168.l.1 or 192.168.l.0 – it is time to learn something about Internet Protocol Addresses.

The Internet Protocol (and its most common abbreviation is the IP) is the method or protocol that is applied to transfer data which is located on the Internet from one computer to another one. That is to say, each and every PC (or in other words, the host) that is connected to the Internet has at least one IP address which tells it apart it from the other computers that are also connected to the Internet. In addition, when information is transmitted or being received (such as for example an e-mail or even a Web page), the message is divided into little chunks of information which are dubbed packets. In effect, each packet has the receiver’s and the sender’s Internet addresses. Additionally, each packet is primarily sent to what is called a gateway computer that has the ability to make out a small part of the Internet. After that, the gateway computer proceeds to interpret the address known as the destination one, advancing the packet to something named an adjacent gateway. This gateway in turn continues to interpret the destination address on the Internet up until the gateway I able to identify the packet, thereby considering that the packet is part of a PC within its vicinity. Following this, the gateway continues to advance the packet directly to the address which is specified on the computer.

Recommended Reading : 

How To Reset Your Username and Password on a Linksys Wireless Router

How To Access Your Router If You Forgot The Password

How To Find The Default IP Address Of A Netgear Router


Because each and every message consists of packets, each packet must be able, if so necessary, to be transmitted by a distinctive Internet path way. As it happens, these packets are delivered differently in comparison with how they were transmitted, as the Internet Protocol serves only for conveying messages. There is another type of protocol which is named the Transmission Control Protocol (or TCP in short)which serves for putting the messages in the right kind of order.

In general, the IP is what is called a link less or connectionless procedure or protocol, which simply means there is no permanent connection which links those end points entering into interaction or communication. Thus, every packet making its way through the Internet is regarded as an independent chunk of data with no links with any other data. In fact, these packets are in the end set in a proper order because of the TCP protocol and, as already ascertained, it is a procedure or protocol that is adjusted to linking. Furthermore, it keeps a trace of the chain of a packet contained by a specific message.

Recommended Reading : 

Linksys Wireless Router Reviews


The Internet Protocol address which is used most frequently now is IPv4. This happens to be the 4th version of IP. Although we must say that the 6th version (IPv6) has been gaining plenty of support lately. In fact, this IP version can access IP addresses that are considerably longer, thus giving the option of a larger number of Internet users. Also, this version, which is the latest one, includes the power of Version 4, so that any server that can support the packets of Version 6 can also support those of Version 4.


An IP address is an address which contains a 32-bit numeral that has the ability to identify the senders (and receivers) of information that is forwarded as packets on the Internet, and which is assigned to various devices, such as the computer, routers, mobile devices, and printers. There are two parts in every IP address: 1. an identifier of a specific Internet network, and 2. a device identifier on the network (which means a server or a work station). An IP address contains four numerals which are divided by periods or full stops. This is very important because typing the small letter L in the IP is wrong and most people are doing it – 192.168.l.1 and 192.168.l.0 looks the same as, but it is not the same. It will end up in an error. The numerals which form these kinds of addresses are called octets (due to the fact that there are 8 positions in a binary representation which contains 32 bits). Also, every position in a binary form is either in an on or an off (1 / 0) state, although here is a sum potential combining of 256 per octet numerals. So, with potential octets within one IP address, roughly 4.3 billion possible values are possible. Of these, there exist so called restricted addresses which are not used for IP addresses. An instance of this is, which is employed only for network broadcasting,, which is for default network addresses, as well as which is the so called loopback address used by clients or host computers.

A standard example of a customary home network uses an IP address that begins its sequence by means of the following line of number – 192.168. By and large, these addresses appear like these two – and It is important to know that the IP is made of numbers, not letters – so 192.168.l.1 and 192.168.l.0 is not a valid IP address although many users make this mistake.

There are two basic reasons why IP addresses are used: the first one is location addressing and the second one is network identifying. These addresses were initially created with the purpose of preventing the addresses of the IP version 4 from overload.


A public IP address is one which the Internet has access to. In fact, like mail addresses for delivering mail to our homes, an IP address which is public is the distinctive and one-only IP address which is allocated to a device. If you wish to find the public IP address which you are using, it is found at the page called ‘What is my IP Address.’


On the other hand, a private IP address, in our case, is for assigning to devices, that us, computers in our private space but without allowing them to be directly exposed to the Internet. To illustrate, in the case that there are multiple devices in our home, we perhaps would want to use these private addresses for each and every device at home. If this is the state of affairs, our router will have a public IP address, but all the devices, be they a PC, a smart phone, a tablet or a printer which are linked to the router (by way of Wi-Fi or wired) have private IP addresses from the router and by way of the DHCP protocol.

The organization which registers IP address ranges to ISPs (Internet Service Providers) and various organizations is called IANA or the Internet Assigned Numbers Authority. In order to let organizations allocate private Internet Protocol addresses, the InterNIC (or the Network Information Center) earmarks specific blocks of addresses for private usage.

All in all, a private IP address entails the following: this is the specific address space which is assigned by the InterNIC center in order to let various organizations make their very own private networks. In fact, there are 3 blocks of IP which are reserved for private usage (these are 1 class A, followed by 1 class B, then 1 class C). Private IP addresses, as has already been mentioned, are most often allocated to PCs, smart phones, printers, and tablets in your home, and PCs used by organizations. Thereby, when a PC is allocated this address, the devices in our home can see this computer by way of its private Internet Protocol address. On the other hand, the devices which are located externally from the local network do not have the capacity for direct communication by way of the private IP address. Rather, they use the public IP address of the router for communication. In order to permit direct access for a device that is allocated a private IP address, it is necessary to use a NAT (or a Network Address Translator).

In conclusion, this kind of Internet Protocol address generally entails that a router cannot be connected in the case that this address is utilized externally (from the home network). It is called a private address due to the fact that it is created inside the router’s firmware (firmware is the kind of software which renders control, monitoring as well as data manipulation). Also, this address permits computer or device access to users by utilizing a browser on the computer by typing in the URL bar (and linked with the router which has a default IP

192.168.l.1 AND 192.168.l.0

Since it is a common mistake which can take you some time to figure out that you are typing the wrong one, we have to say this again – 192.168.l.1 and 192.168.l.0 is wrong, the correct is


The private Internet Protocol address ranges are the following:

As you can see the IP belongs to this IP address range. The address which is our topic – – happens to be a private address on the Internet Protocol. In fact, an address is regarded as private if it is within an address span which is reserved for private use. In fact, these addresses are typically employed on local networks which comprise of business LANs and schools. Thus, a device using a private IP address cannot connect directly with the Internet. Equally, a device which is located externally from the local network cannot link to a device by using a private address in a direct manner. Hence, these links must pass through a device (or, of course, a router) using NAT (short for Network Address Translation) that renders an additional level of safety to the local network. And finally, for the last time, always check if you are typing the IP correctly since 192.168.l.1 and 192.168.l.0 is not an IP address.

4.82/5 (17)

If you like this article, please rate it.

221 thoughts on “

  1. Linksys is now a division of Cisco

  2. How do I change default ip gateway

  3. What is

  4. You get to have Login Admin with this Address

  5. or ADSL modem

  6. Lynksys routers used this ip

  7. enter the IP address, you would have a full authorization on it

  8. username is admin with no password

  9. which password you’ve forgotten?

  10. Still can’t find your pass

  11. Look for your router’s default IP address in your router documentation.

  12. Create long, secure, random password

  13. It shows password of all Wifi networks you have connected Wifi only

  14. How to view someones IP address

  15. how to reset router password to factory settings???

  16. refreshing your IP address can have the same net result

  17. “restart” and “reboot” mean the same thing

  18. internet keeps disconnecting until I restart either my computer

  19. your router may have a larger underlying issue

  20. When the router has rebooted restart the PC

  21. connect to the router using only a wired connection and without the modem

  22. Only one device within a network can use any of the numbers

  23. configure your computer’s IP address manually

  24. Private IP addresses usually begin with 192.168….

  25. You lose one for the network address and one for the broadcast

  26. From what I can understand so far, it describes a range of IP.

  27. All of you explained it very detailed and perfect for me

  28. Reset the router

  29. check the documentation that came with your router

  30. choose WPA2 encryption

  31. set up password protection

  32. Do I need a different number for Wii connect?

  33. i am not able 2 open,it says error 404

  34. I want to change wifi password. But I don’t know who to change

  35. may i know the ranges of public ip address

  36. it should be possible look in your router’s setting

  37. you can change it by the router settings

  38. tried IP with other (Encore) Router

  39. than ‘’ has no significance

  40. All IP addresses are 4 bytes

  41. “DNS_PROBE_NOT_FINISHED_BAD_CONFIG”. Am getting this error message while am browsing internet.

  42. put that address into a web browser, and let us know what happens! Use Http:\\

  43. What is the gateway IP?

  44. DNS

  45. Ive used the tiny reset button.
    still trying to find a password that works…

  46. Ive tried the blank user and admin password, and admin / admin.
    sometimes I can get to the main screen but I ALWAYS get a password request that never works when I click on the administrative tab

  47. After a reset you should use a user ID of admin and a password of admin

  48. If you know the default, then connect into the router utilizing a cable, and get the wifi password from within the router.

  49. can you ping the address?

  50. Change the router channel and it works fine

    I have also been bothered by this problem….

  52. Fixed the problem and my nightmare is over.

  53. wow that was so simple. thanks a lot this problem was haunting me the whole day !

  54. I followed these exact instructions and I still can’t get on the internet even though my computer is telling me it’s connected. Any other suggestions?

  55. You are awesome!! Thank you so much for the helpful advice!!

  56. this worked great! I thought I was going to need to re-image my computer, glad I found this before I did the re-image. Thank so much for posting this info. Great job.

  57. After toiling for days trying to get the laptop to connect, YOU, waved your little magic and did the job. Thanks Heaps. GOLD star for you.

  58. I finally solved my problem:

    From Internet Explorer, when it failed to connect,

    click tools

    internet options


    click “reset”, which resets default settings

    • I tried this below and it worked perfectly for my situation. Thank you so much.

  59. I don’t understand how you can get to the link there if your Internet is not working. Sorry same thing happening to my computer. I just happen to be on my phone. So I’m confused.

  60. Yes helped a lot

  61. I set my login-user and login-password yesterday to someting good, but today i tried every possible password… but noop !!! How can I reset the password or reset the complete router to scratch.

  62. There is a factory-reset button located at the back of the ADSL Router

  63. Username: admin
    Password: admin

  64. You are useless.. how do you connect to WiFi when yo can’t connect to you modem.

  65. i have solution for this problem.if you have tp-link router and wifi router,first connect to your wifi router and open is successfully open.

  66. Type in ipconfig in the command prompt and get the Internet Protocol address of your router at the default gateway.

  67. Hi – log into your router and check the dhcp server range

  68. is anybody thereto helpo me????

  69. I too had same problem.
    to resolve the issue follow this procedure
    go to
    login using admin as userid and default password as admin (if you have not changed it before )
    after login click on management tab
    on ur left hand side there is a option called ” Access Control” click on it
    then select user management and then you can change your UserID and Password

  70. which cable you are using ?????????????

  71. How to connect two systems through LAN…….?

  72. my laptop is not working but I tried it and it was not succsessful!

  73. I had a similar issue. What fixed it for me was resetting the router to the factory settings.

  74. Many routers will not let you access setup from the wireless connection. Be sure you are hardwired (ethernet cable) to the router when trying to access setup.

  75. go to cmd, then type ipconfig /all and chech whats your getway addres.
    Then type ping |your getway addres| -t and chech are there any time outs. If they appeared, I think u have problems with your net cable.

    sorry for my broken english 😀

  76. Hi All,
    My problem got solved after I switched off and on the router and choosing a different port for the cable behind the router.Thanks

  77. thanks

  78. Get IP From Router But Won’t Connect To Out

  79. Thanks for helping me to loggin

  80. Let us know how it goes. Good Luck. 😉

  81. How can i disable the remote access ?

  82. I am using D-Link 2730 U. I want to know that how i can log out from router gateway address. I cant find log out button at gateway address. I look all tabs but did not find.

  83. router pass pls 🙂 🙂 🙂

  84. I think is the first one and popular ip address.

  85. there’s also the to and the to private IP address ranges

  86. Why is almost every modem’s IP and almsot every router is

  87. Can anyone tell me what this means:

    ADSL state – Show Time (in red letters)


  88. Switch everything off, push the reset button at the back of the router with a pin, switch on router, wait a minute or so, switch on PC.

  89. Are you trying to access your router. If so what is it’s make?

    • Yeah – that’s normally the router

  90. Great explanation, thanks

  91. Configuring the modem settings solves the problem, but it is the same again when you turn it on and off.

  92. Click on Wireless router setup

  93. I got same problem on my router. After investigating on this i found that the web server port of my router got changed. For me is working.

  94. username: admin
    pass word maybe leaving the box blan or “admin”

  95. Open a terminal and run the following command:
    ipconfig /flushdns
    ipconfig /renew

Leave a Comment